Materials Testing

Qualimet delivers materials testing results you can decide on

Materials testing results only help if they come with a clear decision attached. Qualimet tests to ABSA pressure requirements, CWB welding qualification and ASME code compliance, and interprets every result against the acceptance criteria your project specifies. That means a pass, a fail or a borderline result all arrive with a clear next step. That interpretation continues past the report itself, until the result actually resolves something for your project.

What Qualimet’s testing capabilities clear for your project

• Metallurgical and destructive testing: Confirms material properties before fabrication, and qualifies welders and procedures to code before work starts.
• Weldment testing: Confirms welded component integrity before installation or turnover.
• Hot tap testing and procedure development: Clears pipeline tie-ins without shutting down the line.
• Profile comparisons: Confirms geometry matches spec before parts move to the next stage.
• Heat treatment: Restores or verifies material properties after fabrication.
• Pressure testing (U, A and B stamps): Clears vessels and piping for service.
• Multi-material testing (metals, polymers, elastomers, composites): Covers mixed-material projects without adding a second lab.
• In-house specimen preparation: Keeps prep consistent so results aren’t skewed before testing starts.

Qualimet applies the same interpretation standard across every one of these capabilities.

A borderline result with no next step is worse than no result at all

A test result that doesn’t come with a clear next step doesn’t actually solve anything, it just adds a data point to a stalled decision. The same block shows up when a material isn’t approved to proceed with fabrication or installation, or when a result is holding up an inspection with no clear path forward. It also shows up when a failed or borderline result leaves your team guessing rather than acting. The borderline case is the one Qualimet hears about most, and by then the schedule has usually already slipped waiting on an answer. Nothing moves again until someone actually interprets what the number means.

Most labs hand back a report. Qualimet stays engaged until it’s resolved.

Every result comes with technical interpretation against your project’s real acceptance criteria, so your engineering and QA/QC teams get a decision they can act on. If a result is borderline or fails, Qualimet works through the interpretation with your engineering team until there’s a clear next step. That could mean retesting, a procedure change or documentation for an audit. That continued interpretation is also why clients see fewer repeat failures, since the data points to a cause the first time.

How a Qualimet test result actually gets resolved

1. Test to the governing standard: Qualimet tests to ABSA, CWB and ASME requirements, prepared entirely in Qualimet’s own 4,800-square-foot facility.
2. Interpret against your acceptance criteria: Every result gets checked against what your project’s specification actually requires.
3. Deliver a clear next step: A pass, a fail or a borderline result all arrive with a documented path forward for your team.
4. Stay engaged through resolution: If the answer isn’t final yet, Qualimet works with your engineers on retesting, a procedure change or documentation until it is.

Qualimet’s credentials

Every result Qualimet delivers is backed by real credentials, plus ISO 17025 accreditation (6108.01) for our own lab. We’re CWB-certified and hold an ABSA Certificate of Authorization. We’re also an APEGA permit holder, with P.Eng. registrations across six jurisdictions: British Columbia, Alberta, Saskatchewan, Manitoba, Ontario and the Yukon. We run our own in-house testing lab and have operated since 1973. 

Interpretation attached to testing gets your project moving faster

Once testing comes with real interpretation attached, fabrication and installation get released faster, inspection failures and retests drop and documentation is ready for an audit the day it’s issued. Qualimet’s Materials Testing work rolls up two connected services. Material Failure Analysis covers root-cause investigation after something’s already failed, and Metallurgical Testing Services covers the ISO 17025-accredited testing itself. Related support: Metallurgical Consulting.

Qualimet materials testing questions

Will testing delay my project schedule further?

Testing is often the fastest way to keep a project moving. Qualimet builds turnaround around your production schedule and flags borderline results early, with a clear path to resolution. Our goal on every job is fabrication or installation proceeding as soon as the data actually supports it.

How does Qualimet handle a failed or borderline result?

A failed or borderline result isn’t the end of the conversation. Our team interprets it against your project’s acceptance criteria and works with your engineers on the next step. That could be a retest, a procedure change or documentation to support an inspection or audit.

Will your results hold up during an audit?

Every result is documented against the standard or specification it’s tested to, including ABSA, CWB and ASME requirements and our lab holds ISO 17025 accreditation. That traceability is built into the process, so your results are audit-ready when they’re issued. We build that documentation into every test from the start.

Is fast turnaround the same as good testing at Qualimet?

No. Turnaround only matters if the result is accurate and interpreted correctly. A fast result that doesn’t hold up under review costs more time than a properly interpreted one, since it usually means retesting later. We scope turnaround around your schedule without cutting the interpretation, and we hold both requirements to the same standard on every job.

What types of materials can be tested?

Qualimet tests metals, polymers, elastomers and composites, along with weldments, pressure components and heat-treated parts. All specimens are prepared in-house, so results stay consistent across material types. We keep the same interpretation standard applied across every one of those material types, so your project can run through several without adding a second lab.

What’s the difference between metallurgical testing and materials testing?

Materials testing is the broader category, covering any test that confirms whether a material or component meets a required property or standard. Metallurgical testing is the specific discipline focused on metals, their structure and how they behave under stress, heat or a weld. Qualimet’s Materials Testing covers both, with Metallurgical Testing Services as the ISO 17025-accredited piece focused specifically on metals. We apply the same interpretation standard to a metallurgical result as to any other material type it tests, so your project gets one consistent process either way.